No Hot Water? The Five-Minute Checks to Run Before You Call a Plumber

No Hot Water, Check this first

Table of Contents

The shower has gone cold, or the kitchen tap won’t warm up no matter how long you run it. When your hot water system is not working, the cause is often something you can rule in or out in a few minutes, before you ring anyone. 

Work through the checks below in order. They follow the order the risk actually occurs: 

  • Safety first, in case there is gas in the air 
  • Then the power supply, for electric systems 
  • Then the gas supply, for gas systems 
  • Then what your result is telling you, and when to stop 

If you smell gas, stop here 

This is the one fault nobody should troubleshoot. If you can smell gas, stop and get out. This is not a DIY job. 

Natural gas has a strong rotten egg smell added so a leak is easy to notice. If you pick it up near the unit or anywhere in the house: 

  • Don’t try to relight the pilot or touch the unit 
  • Don’t use light switches, phones or anything that could spark near the smell 
  • Get everyone out of the house 
  • From outside, call your gas distributor’s emergency line (it’s printed on your gas bill), or 000 if there is an immediate danger to life or property 


Once the area is safe, any repair to the gas supply or the unit needs
licensed gas fitting. If there’s no smell of gas, carry on to the checks for your system type. 

Electric system: the three things to check, in order 

If anything near the unit or the switchboard is wet, don’t touch it. Skip straight to calling a plumber. 

  1. The isolation switch. This is usually a wall switch near the tank or beside the switchboard, often labelled “hot water”. Make sure it’s on. It gets bumped off more often than you’d think. 
  2. The switchboard breaker. Look for a circuit labelled hot water or HWS. If it has tripped, switch it back on once. If it trips again, leave it off and call for help. 
  3. The high-limit reset button. Most electric storage tanks have a safety cut-out that switches the element off if the water overheats. The reset steps are further down this page, because this is the one people most often get wrong. 


After any of these, allow up to an hour for the tank to recover before you decide it hasn’t worked. Many Melbourne homes also run their electric tank on an off-peak tariff, so if the house has used a lot of hot water today, the tank may simply be empty until it reheats overnight.
 

Gas system: the three things to check, in order 

Only run these if there is no smell of gas. 

  1. The supply valve. Find the gas pipe going into the unit. On most valves, a handle in line with the pipe means open and a handle across the pipe means closed. 
  2. The pilot light. Many gas storage tanks have a small viewing window near the base. If you can’t see a flame, the pilot has gone out. Some units carry relighting steps on the label, but if you’re not comfortable following them, leave it to a licensed gas fitter. Continuous-flow units have no pilot, so check the display for an error code and make sure the unit’s power point is switched on. 
  3. A supply outage in the street. Try the gas cooktop or heater. If nothing else on gas works either, the problem may sit with the supply, not your unit. Your gas bill names your distributor, who can tell you about outages in your area. 

What the result tells you when your hot water system is not working 

Your checks have already narrowed things down. Here’s how to read what you found: 

  • The reset holds and hot water comes back. Good news for today, but the cut-out tripped for a reason. A thermostat or element is usually starting to fail, so book a check before it happens again. 
  • The reset trips again straight away. That points to the element itself. It needs replacing, and that’s a job for a licensed tradie. 
  • No power at all. The switch and breaker are on, but the unit is dead. The fault sits somewhere between the switchboard and the tank, and it needs a qualified person to trace it. 
  • Water at the base. Water pooling around the bottom of the tank, or weeping from the element seal, usually means the cylinder or a seal has failed. That’s often a replacement conversation rather than a repair. 

How to reset your hot water system safely 

The step most people get wrong is pressing the button with the power still on, or pressing it again and again. Do it this way instead: 

  1. Switch the unit off at the isolation switch and at the switchboard. 
  2. Find the reset button. On many electric tanks it sits behind a small access cover near the element. 
  3. If that cover needs tools to remove, stop here. There are live parts behind it, so leave it for a licensed tradie. 
  4. If the button is easy to reach, press it firmly once. You may feel a click. 
  5. Switch the power back on. 
  6. Wait up to an hour before you test a hot tap. 


Why wait the full hour? The tank has to heat a whole cylinder of cold water from scratch. Running the hot tap too early just draws more cold water in, and it can look like the reset failed when it didn’t.
 

If you press the button and there is no click, or the power trips again once you switch it on, don’t keep trying. The fault is still there. 

Three symptoms that mean stop, do not wait 

Usually, putting the kettle on and giving the tank an hour is fine. With these three, it’s the wrong call: 

  • Water pooling at the tank base. Switch the unit off at the isolation switch and, if you can reach it safely, turn off the cold water valve on the pipe feeding the tank. 
  • A burning smell. Switch the power off at the switchboard and keep clear of the unit. 
  • Hot water that keeps cutting in and out. Constant cycling can mean a failing thermostat or a safety device tripping over and over. Turn the unit off and get it looked at. 


For any of these, call a
24/7 emergency plumber rather than waiting for business hours. 

Calling a hot water service in Altona: what happens when a plumber arrives 

Every hot water service Altona residents book with us follows much the same path you’ve just walked: 

  • Confirm the power or gas supply is reaching the unit 
  • Test the thermostat and element on electric units, or the burner and pilot on gas units 
  • Check the valves and look over the tank for corrosion or leaks 
  • Tell you plainly whether it’s a repair or a replacement 


That last point is where the age of the unit changes the answer. You’ll usually find the manufacture date on the compliance label on the side of the tank. On a newer tank, a failed element or thermostat is normally worth fixing. On an older tank showing rust or weeping at the base, a new part may only buy a few months before the cylinder itself gives out. A good plumber will weigh the two and tell you which way they’d go.
 

Our team repairs thermostats, elements, burners and valves, and carries common parts in the van so many repairs can be done in the same visit. If you’re unsure who should be working on your system, here’s why licensing matters. 

FAQs 

Why is hot water suddenly not working? 

The most common causes are a switched-off isolation switch, a tripped breaker, a tripped high-limit cut-out, or a pilot light that has gone out. Less often, it’s a failed element or thermostat, or a gas supply problem in the street. The checks above rule each one in or out. 

How to reset a hot water system? 

Turn the power off at the isolation switch and switchboard first. If the reset button is easy to reach, press it once firmly, restore power, then wait up to an hour. If the button sits behind a cover that needs tools, leave it for a licensed tradie. 

What is the first thing to check when there is no hot water? 

First, make sure you can’t smell gas. If you can, get out and call your gas distributor’s emergency line. If not, check the isolation switch on an electric unit or the supply valve on a gas unit. 

Why would my hot water not work but my cold water does? 

Your cold water comes straight from the mains, while hot water depends on the heater. So cold water flowing normally tells you the supply is fine and the fault sits with the hot water system itself: power, gas, pilot, thermostat or element. 

Tips to keep your hot water running 

  • Book an annual anode check. The anode protects the inside of the tank from corrosion, and a worn one can shorten the tank’s life. 
  • Keep the area around the unit clear. Boxes, garden gear and rubbish around the tank make it harder to spot leaks, and gas units need room to breathe. 
  • Know where your isolation switch is before you need it. Find it now and label it, so anyone in the house can turn the unit off quickly. 

Still no hot water? 

If you’ve worked through the checks and the shower is still cold, our licensed team can find the fault and talk you through repair or replacement. Learn more about hot water systems in Altona, or if it can’t wait, call a 24/7 emergency plumber. Your local plumber in Altona is a phone call away. 

Picture of Plumber in Altona

Plumber in Altona

Share this article

Get a Free Quote